Olivia Carter
If you are looking to change the door round on your Servis fridge freezer, this guide will provide you with step-by-step instructions on how to do it. Whether you need to replace a damaged door round or simply want to give your appliance a fresh look, this process is relatively straightforward and can be done with a few basic tools.
Before you begin, make sure you have the new door round that matches your Servis fridge freezer model. You can usually find replacement parts at an appliance store or order them online. Once you have everything you need, follow these simple instructions to change the door round:
- Start by unplugging your Servis fridge freezer to ensure your safety while working on it.
- Open the door and locate the screws that hold the old door round in place. Depending on your model, there may be multiple screws around the perimeter of the door or a single screw at the top or bottom.
- Use a screwdriver to remove the screws and gently pull the old door round away from the door. Be careful not to damage any other components.
- Take the new door round and align it with the holes where the old one was located. Make sure it is positioned correctly before proceeding.
- Secure the new door round in place by tightening the screws. Make sure they are snug but be careful not to overtighten as this can strip the holes or damage the door.
- Once the new door round is securely attached, plug in your Servis fridge freezer and switch it on to make sure everything is functioning correctly.
Changing the door round on your Servis fridge freezer is a relatively simple process that can make a big difference in the appearance of your appliance. Follow these step-by-step instructions to ensure a proper installation and enjoy the fresh new look of your fridge freezer.
Getting Started: Preparing for Door Round Replacement
Before you begin replacing the door round on your Servis fridge freezer, it’s important to gather all the necessary tools and materials. This will ensure a smooth and efficient installation process.
Here’s what you’ll need:
1. Replacement door round: Make sure you have the correct size and model number for your Servis fridge freezer. You can purchase a genuine replacement part from the manufacturer or an authorized dealer.
2. Screwdriver: Depending on the specific model of your Servis fridge freezer, you may need either a Phillips or a flathead screwdriver to remove the screws securing the old door round in place.
3. Protective gloves: It’s important to wear gloves to protect your hands from any sharp edges or potential injury during the door round replacement process.
4. Cleaning supplies: Take the opportunity to clean the interior and exterior of your fridge freezer while the door round is removed. This will help maintain hygiene and a fresh appearance.
5. Work surface: Prepare a clean and flat work surface where you can safely place the door round and perform the replacement. This will prevent any damage to the new door round during the installation process.
Important precautions:
1. Disconnect the power: Before starting any repairs or replacements, always unplug the fridge freezer from the power source to avoid electric shock or damage to the appliance.
2. Take measurements: Before removing the old door round, measure its dimensions and note any details that may be helpful during the installation of the new door round.
3. Follow safety guidelines: Read the manufacturer’s instructions and safety guidelines before attempting the door round replacement. This will ensure a safe and successful installation process.
By gathering all the necessary tools and materials and taking the necessary precautions, you’ll be well-prepared for replacing the door round on your Servis fridge freezer.
Gathering the necessary tools
Before you begin the process of changing the door round on your Servis fridge freezer, it’s important to gather all the necessary tools. Having the right tools on hand will make the process much easier and ensure that you don’t damage any parts of the appliance. Here are the tools you will need:
- Flathead screwdriver
- Phillips screwdriver
- Adjustable wrench
- Hammer
- Tape measure
- Masking tape
- Putty knife
- Level
Make sure to have these tools ready before you start working on changing the door round. It’s also a good idea to have a clean workspace and sufficient lighting to make the process easier and safer.
Disconnecting the power supply
Before changing the door round on your Servis fridge freezer, it is important to disconnect the power supply to ensure your safety and avoid any electrical hazards. Follow the steps below to properly disconnect the power supply:
| Step | Instructions |
|---|---|
| Step 1 | Locate the power cord of your Servis fridge freezer. |
| Step 2 | Unplug the power cord from the electrical outlet. |
| Step 3 | Check if there is a switch or button near the power cord. If so, turn it off. |
| Step 4 | If your fridge freezer is connected to a circuit breaker, locate the specific breaker and switch it off. |
| Step 5 | Wait for a few minutes to ensure that all electrical components are completely switched off. |
By properly disconnecting the power supply, you can proceed with changing the door round on your Servis fridge freezer with peace of mind, knowing that you have taken the necessary safety precautions.
Removing the Old Door Round
To change the door round on your Servis fridge freezer, you’ll first need to remove the old door round. Follow the steps below to safely remove the old door round:
| Step 1: | Open the fridge freezer door and locate the screws holding the door round in place. |
| Step 2: | Using a screwdriver, gently unscrew the screws from the door round. |
| Step 3: | After removing the screws, carefully lift the old door round off the fridge freezer door. |
| Step 4: | Place the old door round aside and make sure not to damage it in the process. |
| Step 5: | Inspect the door round and the area where it was attached for any damage or dirt. |
With the old door round successfully removed, you are now ready to install the new door round on your Servis fridge freezer.
Opening the freezer door
To change the door round on your Servis fridge freezer, you need to start by opening the freezer door. Here is a step-by-step guide on how to do it:
- Ensure that the fridge freezer is turned off and unplugged from the power source for safety.
- Locate the handle on the freezer door. This is usually on the front and can be a vertical or horizontal grip depending on the model of your fridge freezer.
- Gently pull the handle towards you to release the door latch.
- Once the door latch is released, grip the sides of the freezer door firmly with both hands.
- Pull the door towards you slowly and steadily, ensuring that you have a good grip to prevent the door from falling.
- Continue pulling until the door is fully open.
Now that you have successfully opened the freezer door, you are ready to proceed with changing the door round on your Servis fridge freezer. Refer to the manufacturer’s instructions or the user manual for further guidance on this process.
Unscrewing the screws
To change the door round on your Servis fridge freezer, you will need to unscrew the screws that secure the current door in place. Here is a step-by-step guide:
| Step 1: | Locate the screws that hold the door hinges in place. These screws are typically located on the inside of the door. |
| Step 2: | Using a screwdriver, insert the tool into the screw head and turn counterclockwise to loosen the screws. |
| Step 3: | Continue unscrewing the screws until they are completely loosened. Be careful not to drop the screws or misplace them. |
| Step 4: | Once all the screws are loosened, gently lift the door away from the fridge freezer and set it aside. |
By unscrewing the screws and removing the current door, you can now proceed to attach the new door round on your Servis fridge freezer. Make sure to follow the manufacturer’s instructions and securely tighten the screws to ensure the door is properly attached.
Installing the New Door Round
Once you have removed the old door round from your Servis fridge freezer, it’s time to install the new one. Follow these steps to ensure a successful installation:
Step 1: Prepare the New Door Round
Before installing the new door round, make sure it is free of any packaging materials or protective films. Clean the surface of the round with a mild detergent and water solution to remove any dirt or residue.
Step 2: Align the Door Round
Place the new door round in the desired position on the fridge freezer door. Align it carefully so that the screw holes on the round match up with the holes on the door.
Step 3: Secure the Door Round
Using a screwdriver, carefully insert the screws provided with the new door round through the screw holes and into the corresponding holes on the door. Tighten the screws gently until the round is securely attached to the door. Be careful not to overtighten, as this may cause damage.
Once the door round is securely attached, give it a gentle tug to ensure it is properly connected to the door. If it feels loose or moves easily, you may need to tighten the screws further.
Note: If the door round came with any additional accessories, such as plastic caps or trim pieces, carefully install them according to the manufacturer’s instructions.
Step 4: Test the Door Round
With the new door round installed, open and close the fridge freezer door several times to ensure it operates smoothly. Check for any misalignments or rubbing that may be caused by the new round. Make any necessary adjustments or tighten the screws further if needed.
By following these steps, you can easily install the new door round on your Servis fridge freezer. Enjoy the refreshed look of your appliance!
Aligning the new door round
Once you have successfully removed the old door round from your Servis fridge freezer, it’s time to align and attach the new door round. Follow these steps to ensure proper alignment:
1. Prepare the new door round
Before attaching the new door round, make sure it is clean and free from any dust or debris. Also, ensure that all necessary accessories or hardware, such as screws or hinges, are included and ready for use.
2. Check the alignment of the fridge freezer
Before attaching the new door round, ensure that the fridge freezer is level and properly aligned. Use a level or measuring tool to verify this. If necessary, adjust the fridge freezer’s legs or position to achieve proper alignment. This will help ensure that the new door round fits correctly.
3. Align the hinges
Align the hinges of the new door round with the hinge holes on the fridge freezer. Carefully insert the hinges into the corresponding holes, ensuring a snug fit. Take your time and make any necessary adjustments to ensure proper alignment.
4. Secure the door round
Once the hinges are properly aligned, use the supplied screws or hardware to secure the door round to the fridge freezer. Start with one screw and gradually tighten the rest while ensuring that the door remains aligned. Do not overtighten the screws, as this may cause damage.
5. Test the door round
After securing the door round, gently open and close it to ensure smooth operation. Check for any gaps or misalignment and make further adjustments if necessary. Remember to test the door’s seal to ensure it closes properly and maintains the desired temperature inside the fridge freezer.
Following these steps will help you properly align and attach the new door round on your Servis fridge freezer. If you encounter any difficulties or have further questions, refer to the manufacturer’s instructions or seek professional assistance.
