Olivia Carter
If your Fridge Freezer Cw796 is not cooling properly or is running constantly, it might be time to consider changing the thermostat. The thermostat is responsible for regulating the temperature inside the fridge, and if it is faulty, it can lead to various issues. Don’t worry, changing the thermostat is a relatively simple task that you can easily do yourself.
Step 1: Unplug the Fridge Freezer
Before you begin any work on your appliance, it is important to ensure that it is not connected to the power supply. Unplug the fridge freezer from the electrical outlet to avoid any accidents or electrical shock.
Step 2: Locate the Thermostat
The thermostat is usually located at the back of the fridge freezer, near the top. Remove any shelves or panels that may be blocking your access to the thermostat. Once you have a clear view, you should be able to see a small dial or knob that controls the temperature settings.
Step 3: Remove the Old Thermostat
Using a screwdriver, carefully unscrew the mounting screws that secure the thermostat in place. Gently pull the thermostat out from its housing, being cautious not to damage any of the connecting wires. Take note of how the wires are connected to the thermostat, as you will need to reconnect them to the new thermostat later.
Step 4: Install the New Thermostat
Take your new thermostat and carefully connect the wires to the corresponding terminals. Make sure the connections are secure and tight. Place the thermostat back into its housing and use the mounting screws to secure it in place.
Step 5: Test the Fridge Freezer
Once you have successfully replaced the thermostat, plug the fridge freezer back into the electrical outlet. Set the temperature to your desired setting and monitor the fridge freezer over the next few hours to ensure it is cooling properly and maintaining the set temperature.
Following these steps should help you change the thermostat on your Fridge Freezer Cw796 and restore its functionality. If you are uncertain or uncomfortable with performing any of these steps, it is always best to consult a professional technician for assistance.
Step 1: Gather the necessary tools
Before you can start replacing the thermostat on your fridge freezer CW796, you will need to gather a few tools to help you with the process. Here is a list of the tools you will need:
- Flathead screwdriver
- Phillips screwdriver
- Needle-nose pliers
- Multimeter
- Replacement thermostat
Make sure you have all the necessary tools on hand before you begin, as this will make the process much smoother.
Step 2: Turn off the power to the fridge freezer
Before beginning any work on the thermostat of your fridge freezer, it is crucial to ensure that the power is turned off. This will not only protect you from any potential electrical hazards but also prevent damage to the appliance.
Locate the plug of the fridge freezer and unplug it from the electrical outlet. If the outlet is not easily accessible, you may need to turn off the power supply at the main circuit breaker.
Check that the fridge freezer is no longer receiving power by confirming that the interior lights and the unit’s display panel are off. Additionally, try plugging in a different device to the same outlet to see if it receives power.
Once you have confirmed that the power is off, you can proceed to the next step of the thermostat replacement process.
Step 3: Locate the thermostat
Locating the thermostat is an essential step in changing the thermostat on your fridge freezer CW796. The thermostat is responsible for regulating the temperature inside your fridge freezer, so it’s crucial to find it before proceeding with the replacement process.
The thermostat is typically located behind the control panel on the front of the fridge freezer. To access it, you may need to remove the screws or clips that secure the panel in place. Refer to the user manual or manufacturer’s instructions for specific details on how to remove the control panel.
1. Unplug your fridge freezer
For safety reasons, it’s important to disconnect the power supply to your fridge freezer before attempting any repairs. Locate the power cord at the back of the appliance and unplug it from the power outlet.
2. Remove the control panel
Once you’ve unplugged your fridge freezer, you can begin removing the control panel to access the thermostat. Use a screwdriver or a suitable tool to remove any screws or clips holding the panel in place. Take care not to damage the panel or any of the components behind it.
Tip: If you’re unsure how to remove the control panel, consult the user manual or contact the manufacturer for assistance.
3. Locate the thermostat
With the control panel removed, you should be able to see the thermostat. It is a small device with wires connected to it. The thermostat is usually located near the top of the fridge freezer, close to the cooling mechanism.
Note: In some models, the thermostat may be located in a different position. Refer to the user manual or contact the manufacturer if you’re having trouble finding it.
Once you have located the thermostat, you’re ready to proceed to the next step of replacing it. Make sure to take note of how the wires are connected before disconnecting them, to ensure you can reconnect them correctly with the new thermostat.
Step 4: Remove the protective cover
Before you can access the thermostat, you’ll need to remove the protective cover that is usually located on the front or back of the fridge freezer. This cover is designed to protect the internal components of the appliance and must be removed carefully to avoid damaging any of the parts.
Start by locating the screws or clips that are holding the protective cover in place. Depending on the make and model of your fridge freezer, these may be located along the edges or corners of the cover. Use a screwdriver or a set of pliers to carefully remove the screws or release the clips.
Once all the screws or clips have been removed, gently lift the protective cover away from the appliance. Be cautious not to pull too hard or apply excessive force, as this can cause damage to the cover or the internal components of the fridge freezer.
Set the protective cover aside in a safe place to prevent any damage or misplacement. You may need to reattach it later once the thermostat has been replaced.
With the protective cover removed, you now have access to the thermostat located within the fridge freezer. Proceed to the next step to learn how to replace the thermostat.
Step 5: Disconnect the wires
Before you can replace the thermostat on your fridge freezer, you will need to disconnect the wires to the old thermostat. This will allow you to remove the old thermostat and replace it with the new one.
Start by locating the wires connected to the thermostat. Depending on the make and model of your fridge freezer, these wires may be connected directly to the thermostat or they may be connected to a wire harness that is connected to the thermostat.
Carefully remove the wires from the old thermostat by gently pulling on them. If they are connected to a wire harness, you may need to squeeze the release tabs or use a small flathead screwdriver to carefully pry the harness apart.
Take note of how the wires were connected to the old thermostat so that you can correctly connect them to the new thermostat. If necessary, take a picture or make a diagram to help you remember.
Once the wires are disconnected, you can set the old thermostat aside. Make sure to handle it with care to avoid damaging any of the components.
Now you are ready to install the new thermostat on your fridge freezer. Proceed to the next step for further instructions.
Step 6: Remove the old thermostat
Once you have disconnected the power supply, it is time to remove the old thermostat from your fridge freezer. This component is typically located near the evaporator coils or on the side wall of the freezer compartment. Refer to the user manual or consult a professional if you are unsure of its exact location.
Before proceeding, it is essential to ensure that the freezer is completely defrosted and empty. Any remaining ice or frost can impede the removal process and potentially damage the thermostat or other components.
To remove the old thermostat:
- Locate the screws or clips holding the thermostat in place.
- Use a screwdriver or pliers to loosen and remove these screws or clips.
- Gently pull the old thermostat away from the wall or coils, being careful not to damage any surrounding components.
- Detach any wires connected to the thermostat. Take note of their position or take a picture for reference.
- Once all wires are disconnected, carefully remove the old thermostat from the fridge freezer.
Place the old thermostat aside, as it may be required for warranty claims or troubleshooting purposes. You can now proceed to install the new thermostat in the next step.
Step 7: Install the new thermostat
Now that you have removed the old thermostat, it’s time to install the new one. Follow the steps below to properly install the new thermostat:
- Take the new thermostat out of its packaging and ensure it is the correct replacement for your fridge freezer model.
- Position the new thermostat in the same location where the old one was installed.
- If there are any wires attached to the old thermostat, carefully detach them by loosening the screws or clips that hold them in place.
- Attach the wires to the corresponding terminals on the new thermostat, making sure they are securely fastened.
- Once the wires are connected, align the thermostat with the mounting bracket and carefully push it into place.
- Use a screwdriver to tighten any screws or clips that secure the thermostat in place.
- Verify that the thermostat is properly installed by gently pulling on it to ensure it is secure.
After you have completed the installation, double-check all the connections to make sure they are secure. Once you are confident that everything is properly installed, you can move on to the next step in the process.
Step 8: Test the new thermostat
Once you have replaced the old thermostat with the new one, it’s time to test if it’s working correctly.
Plug the refrigerator back into the power outlet and turn it on. Set the temperature control dial to the desired setting and wait for a few minutes. The compressor should kick in, and you should be able to hear and feel the airflow in the freezer section.
Check the temperature inside the freezer using a thermometer. It should start dropping gradually and reach the desired temperature within a couple of hours. If the temperature remains constant or doesn’t drop at all, there may be an issue with the new thermostat, and you may need to repeat the replacement process or seek professional assistance.
Ensure that the refrigerator is properly sealed and that there are no leaks or gaps in the door gaskets. This can affect the overall temperature and make the thermostat appear faulty.
Monitor the refrigerator’s performance over the next few days to ensure that it maintains the desired temperature consistently. If you notice any issues or abnormal behavior, consult the user manual or contact the manufacturer for further assistance.
Remember to dispose of the old thermostat properly, following local guidelines for hazardous waste disposal if applicable. Also, keep the user manual and any related documentation for future reference or troubleshooting.
FAQ
What is a thermostat?
A thermostat is a device that regulates the temperature in a fridge freezer by turning the cooling system on or off.
Why would I need to change the thermostat on my fridge freezer?
You may need to change the thermostat if your fridge freezer is not cooling properly or if it is constantly running or not running at all.
How do I know if the thermostat on my fridge freezer needs to be changed?
If you notice that the temperature inside your fridge freezer is not consistent, or if it is freezing everything inside, it may be a sign that the thermostat needs to be replaced.
