Olivia Carter
If you recently purchased a Beko Fridge Freezer and realized that the doors are opening in the wrong direction, don’t worry! Reversing the doors on your Beko appliance is easier than you might think. By following a few simple steps, you can easily change the door swing to suit your kitchen layout and personal preference.
To begin, make sure you have the necessary tools handy. You will need a screwdriver, a drill with a 4mm bit, masking tape, and a protective cloth or towel. It’s important to work methodically and take your time to avoid any damage to your fridge freezer.
Start by emptying the appliance and turning it off at the mains. This will prevent any accidents and ensure your safety throughout the process. Next, remove any shelves or drawers from the fridge and freezer compartments to make it easier to access the door hinges. Refer to the user manual for instructions on how to remove these components.
Once you have access to the door hinges, use the screwdriver to remove the screws that hold the hinges in place. It’s best to have someone assist you during this step to hold the door steady. Once the screws are removed, carefully lift the door off the appliance and set it aside on a soft surface. Be sure to protect the door from any scratches or damage.
Now it’s time to remove the hinge covers. These covers are usually located on the opposite side of the door and can be simply popped off with your fingers. Once the hinge covers are removed, use the drill and 4mm bit to remove the screws holding the hinges in place on the opposite side. Make sure to keep these screws in a safe place, as you will need them later.
With the hinges removed, you can now attach them to the opposite side of the appliance. Line up the hinges with the existing holes and secure them in place using the screws you removed earlier. Be sure to tighten the screws firmly, but not too tight to avoid damaging the appliance. Finally, replace the hinge covers and reattach the door by aligning it with the hinges and securing it with the screws.
Once the door is securely attached, double-check that it swings open and closes smoothly. If everything looks and feels right, you can now power on your Beko Fridge Freezer and start enjoying its new door configuration. Remember, practice patience and caution throughout the process, and you’ll soon have a Beko appliance that fits perfectly into your kitchen layout.
Steps to Reverse Doors on Beko Fridge Freezer
To reverse the doors on your Beko fridge freezer, follow the step-by-step instructions below:
1. Turn off the fridge freezer and unplug it from the power source to ensure safety during the door reversal process.
2. Empty the contents of the fridge freezer, including all shelves, drawers, and food items. This will make it easier to work with the appliance.
3. Locate the plastic plugs covering the hinge holes on the opposite side of the fridge freezer. Gently remove these plugs using a flat-head screwdriver.
4. Using a suitable tool, such as a spanner or socket wrench, unscrew the screws securing the top hinge and then the bottom hinge. Keep these screws safe as you will need them later.
5. Carefully lift off the fridge door from the bottom hinge and place it in a safe location. Be cautious as the door may be heavy.
6. Repeat step 5 for the freezer door, ensuring that you keep track of any washers or spacers that may be present on the hinges.
7. Take the top hinge and unscrew it from the opposite side of the fridge freezer. Carefully reposition the hinge on the opposite side, aligning it with the holes that you uncovered by removing the plastic plugs.
8. Secure the top hinge in place using the screws that you originally removed, ensuring they are tightened securely.
9. Repeat step 7 and step 8 for the bottom hinge, making sure that the door is properly aligned with the fridge freezer.
10. Place the fridge door onto the bottom hinge and align it with the top hinge. Carefully lower the door onto the hinge, ensuring it is properly seated.
11. Repeat step 10 for the freezer door, ensuring that both doors are properly aligned and functional.
12. Insert the plastic plugs into the hinge holes on the original side of the fridge freezer, covering the holes for a clean and finished look.
13. Plug the fridge freezer back into the power source and turn it on. Allow the appliance to cool down before placing food items back inside.
By following these steps, you can successfully reverse the doors on your Beko fridge freezer and customize it to suit your specific needs and kitchen layout.
Tools Required for the Door Reversal Process
Reversing the doors on your Beko fridge freezer is a simple process that can be done with a few basic tools. Before you begin, make sure you have the following tools on hand:
1. Screwdriver
A screwdriver is essential for removing the screws that hold the door hinges in place. Make sure you have a Phillips screwdriver that is the right size for the screws on your Beko fridge freezer.
2. Allen wrench
An allen wrench may be needed to remove any additional screws or bolts that secure the door hinges. Check the manufacturer’s instructions for your specific model to see if an allen wrench is required.
3. Putty knife
A putty knife can be useful for prying off any plastic caps or covers that may be hiding screws or bolts. Use the putty knife to gently pry off the caps without damaging them.
4. Tape measure
A tape measure is handy for measuring the distance between the top and bottom hinges. This measurement will ensure that the hinges are properly aligned when you reattach them in the new position.
5. Soft cloth
A soft cloth is useful for protecting the doors and surfaces from scratches or damage during the door reversal process. Use the cloth to cover the fridge freezer while you work on removing and reattaching the doors.
With these basic tools, you should be well-equipped to successfully reverse the doors on your Beko fridge freezer. Remember to consult the manufacturer’s instructions for your specific model to ensure a smooth and successful door reversal process.
Tips for a Successful Door Reversal
If you own a Beko fridge freezer and you’d like to reverse the doors, follow these simple tips for a successful door reversal.
1. Read the instructions
Before you begin the door reversal process, it’s important to thoroughly read the manufacturer’s instructions. Each fridge freezer model may have specific steps or requirements, so familiarize yourself with the instructions to ensure you do the job correctly.
2. Gather the necessary tools
Make sure you have all the necessary tools and materials before starting the door reversal. This may include a screwdriver, wrench, tape measure, and a helper to assist in lifting and aligning the door.
3. Take safety precautions
When reversing the doors on your fridge freezer, always prioritize safety. Ensure the fridge freezer is unplugged before starting the process and take extra care when handling heavy doors or sharp tools. It’s also a good idea to wear protective gloves to prevent any injuries.
4. Remove door handles
First, start by removing the door handles on both the fridge and freezer doors. This is typically done by unscrewing the screws that hold the handles in place. Keep the screws in a safe place as you will need them later.
5. Remove the doors
Next, remove the doors by unscrewing the screws on the hinge that holds each door in place. Pay attention to the number and location of the screws, as this will help you when reassembling the doors in the reversed position.
6. Switch the hinges
To reverse the doors, you’ll need to switch the hinges. Carefully remove the hinges from the fridge and freezer doors and swap them around. This may involve unscrewing screws or pins that hold the hinges in place. Again, keep track of the screws and any other small parts that you remove.
7. Reassemble the doors
After switching the hinges, it’s time to reattach the doors. Align the doors with the hinge holes and insert the screws to secure them in place. Use the screws you removed earlier from the handles and follow the reverse order of the removal process.
8. Attach the handles
Finally, attach the handles back onto the doors in their new position. Make sure they are securely tightened but avoid over-tightening, as this may cause damage to the doors or handles.
By following these tips, you can successfully reverse the doors on your Beko fridge freezer. Remember to take your time, be cautious, and refer to the manufacturer’s instructions for any specific steps or details regarding your particular model.
Common Challenges and Troubleshooting
Reversing the doors on your Beko fridge freezer may seem like a straightforward process, but there can be some common challenges that you may encounter. Here are some troubleshooting tips to help you overcome these challenges:
1. Hinge Reversal: When reversing the doors, the most common challenge is properly reversing the hinges. Make sure to carefully follow the instructions provided in the user manual or installation guide. If you find yourself struggling with this step, it may be helpful to seek assistance from a professional technician or contact Beko customer support for guidance.
2. Alignment: After reversing the doors, it’s important to ensure that they are properly aligned. If you notice that the doors are not closing or sealing properly, the alignment may be off. Check if any screws or bolts need tightening and adjust the alignment accordingly. If the issue persists, consult the user manual or contact Beko customer support for further assistance.
3. Seal Integrity: Another common challenge is maintaining the seal integrity after reversing the doors. If you notice any leaks or drafts, it may indicate that the door seals are not properly installed. Carefully inspect the seals and make sure they are securely attached. If necessary, clean or replace the seals to ensure a tight seal and optimal cooling efficiency.
4. Functionality: After reversing the doors, it’s important to test the functionality of your Beko fridge freezer. Check if the temperature settings are working correctly and ensure that the refrigerator and freezer compartments are cooling properly. If you notice any issues with the functionality, refer to the user manual for troubleshooting tips or contact Beko customer support for assistance.
5. Safety Precautions: When reversing the doors of your Beko fridge freezer, it’s essential to prioritize safety. Always remember to unplug the appliance before starting the process and use caution when handling heavy doors or components. If you have any concerns about your safety or the safety of the appliance, seek professional help instead of attempting to fix the issue yourself.
By keeping these common challenges and troubleshooting tips in mind, you can confidently reverse the doors on your Beko fridge freezer and enjoy the convenience of a properly functioning appliance.
Final Thoughts on Reversing Doors on Beko Fridge Freezer
Reversing the doors on your Beko fridge freezer can be a great solution if you need to change the way your appliance opens. It’s a relatively simple process that can be done at home, with just a few basic tools and some careful attention to detail.
Before you start, it’s important to read the instruction manual that came with your Beko fridge freezer. This will give you specific guidance on how to safely reverse the doors, as well as any additional steps or considerations that may be necessary for your specific model.
One of the most important things to remember when reversing the doors is to take your time and be patient. It’s not a task that should be rushed, as one wrong move could cause damage to your appliance.
Start by emptying the fridge and freezer of all its contents, and remove any shelves or racks that may obstruct your access to the door hinges. Take care to protect delicate items and store them in a cool place while you work.
Next, locate the screws that hold the door hinges in place. You’ll likely need to remove the plastic covers or trim to access them. Use a screwdriver to carefully unscrew these hinges, being mindful not to strip or damage the surrounding area.
Once the hinges are removed, you can carefully lift the door off its current location and place it on the opposite side. Be sure to align it properly with the hinge holes and then reattach the hinges using the screws you removed earlier.
After the door is securely in place on the opposite side, you can also switch the handles if needed. This step may vary depending on your specific model, so consult the instruction manual for guidance.
Finally, double-check that everything is properly aligned and secure before testing the door to ensure it opens and closes smoothly. Take a moment to admire your handiwork, and then transfer your food and belongings back into the fridge and freezer.
Reversing the doors on your Beko fridge freezer can be a bit time-consuming, but with some patience and careful attention to detail, it’s a manageable DIY project. By following the instructions in your appliance’s manual and taking it step by step, you’ll have a fridge freezer that suits your needs and preferences in no time!
FAQ
Can I reverse the doors on my Beko fridge freezer myself?
Yes, you can reverse the doors on your Beko fridge freezer yourself. It may require some tools and a bit of patience, but the process is fairly straightforward.
What tools do I need to reverse the doors on my Beko fridge freezer?
You will need a Phillips screwdriver, a flathead screwdriver, and possibly a 10mm socket wrench. Some models may also require an Allen wrench. It’s always a good idea to consult the user manual for your specific model to see if any additional tools are needed.
